Prepare the pre-heated composite resin

Myoung-Uk Jin

doi:10.5395/rde.2013.38.2.103

Articles

Page Path: HOME > Restor Dent Endod > Volume 38(2); 2013 > Article

Reader's Forum Prepare the pre-heated composite resin: Myoung-Uk Jin; 2013;38(2):-104.
DOI: https://doi.org/10.5395/rde.2013.38.2.103
Published online: May 28, 2013

Kyungbook National University, Korea.

©Copyights 2013. The Korean Academy of Conservative Dentistry.

This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

360 Views
5 Download
4 Crossref

prev next

Full Article

Download PDF

Q.
A.
REFERENCES

Q.

Heating of composite resin prior to use has many benefits. How can I heat composite resin in my clinic?

From Dr. Jong-Hyun Park (Doojung Ye-dental clinic)

A.

Pre-heating of composite resin improves shear bond strength, microhardness value, and degree of conversion. When using composite resin in the clinic, pre-heating the composite resin could be recommended to enhance physical properties.

Another hypothesis for superior physical properties of pre-heated composite resin is that the reduced resin viscosity due to increased temperature might slightly enhance the photoinitiator efficiency, particularly in the case of the twocomponent camphoroquinone/tertiary amine initiator system.1,2 Thus, the enhanced mobility at higher temperatures of both monomer and polymer could produce a significant effect of delaying the vitrification. It is possible that enough camphoroquinone molecules might be converted to the excited triplet state in pre-heated composite to allow adequate propagation of the polymerization reaction for these materials.

Therefore, improved flowability of pre-heated microhybrid or packable resin may result in more accurate adaptation to the marginal area or sharp line angle of the cavity.3,4 As each increment of composite is placed and cured at its ideal polymerization temperature, curing at the elevated temperature might provide improved physical and mechanical properties.

The following methods can be used in your daily practice to pre-heat composite resin.

1. Calset composite warmer (AD Dent)

Calset composite warmer (AdDent, Inc., Dandury, CT, USA) is the most effective method to pre-heat composite resin. This device can heat material to 37℃, 54℃ or 68℃ and also maintain constant temperature.

2. Light of dental unit chair

If you leave composite resin under the light of the unit chair, the temperature of composite resin will be raised. Consequently, microhardness and degree of conversion also increase with elevated temperature of composite resin.

3. Hand holding

If composite resin is wrapped by hand for 3 - 5 minutes, temperature of resin rise slightly.

From Myoung-Uk Jin (Kyungbook National University)

Figure 1

Calset system.

Figure 2

Heating of composite resin under the operating light of unit chair.

Figure 3

Holding composite resin in one hand.

REFERENCES

1. Trujillo M, Stansbury JW. Thermal effects on composite photopolymerization monitored by real-time NIR. J Dent Res 2003;82(special issue A):Abstract 0819.
2. Draughn RA. Effects of temperature on mechanical properties of composite dental restorative materials. J Biomed Mater Res 1981;15:489-495.Article PubMed
3. Covey A, Tahaney SR, Davenport JM. Mechanical properties of heat-treated composite restorative materials. J Prosthet Dent 1992;68:458-461.PubMed
4. Ferracane JL, Condon JR. Post-cure heat treatments for composites: properties and fractography. Dent Mater 1992;8:290-295.Article PubMed

Tables & Figures

Figure 1

Calset system.

Figure 2

Heating of composite resin under the operating light of unit chair.

Figure 3

Holding composite resin in one hand.

REFERENCES

1. Trujillo M, Stansbury JW. Thermal effects on composite photopolymerization monitored by real-time NIR. J Dent Res 2003;82(special issue A):Abstract 0819.
2. Draughn RA. Effects of temperature on mechanical properties of composite dental restorative materials. J Biomed Mater Res 1981;15:489-495.Article PubMed
3. Covey A, Tahaney SR, Davenport JM. Mechanical properties of heat-treated composite restorative materials. J Prosthet Dent 1992;68:458-461.PubMed
4. Ferracane JL, Condon JR. Post-cure heat treatments for composites: properties and fractography. Dent Mater 1992;8:290-295.Article PubMed

Citations

Citations to this article as recorded by

Effect of Preheating of Resin Composite on Microtensile Bond Strength In Vitro Study
M.A. Hanafy, O.M. Fahmy, A.F. Abo Elezz
Open Access Macedonian Journal of Medical Sciences.2024; 12(1): 102. CrossRef
Preheated composite: Innovative approach for aesthetic restoration
Reema N Asani, Vandana J Gade, Kalyani G Umale, Rachana Gawande, Rohit R Amburle, Raksha R Kusumbe, Purva P Kale, Priya R Kosare
Archives of Dental Research.2021; 11(2): 103. CrossRef
Effect of Ultrasonic Vibration on Structural and Physical Properties of Resin-Based Dental Composites
Abdul Samad Khan
Polymers.2021; 13(13): 2054. CrossRef
Color Stability of Ceramic Veneers Luted With Resin Cements and Pre-Heated Composites: 12 Months Follow-Up
Brenda Procopiak Gugelmin, Luiz Carlos Machado Miguel, Flares Baratto Filho, Leonardo Fernandes da Cunha, Gisele Maria Correr, Carla Castiglia Gonzaga
Brazilian Dental Journal.2020; 31(1): 69. CrossRef

CanvasJS.com

ePub Link

Cite

CITE: export Copy Download Format; Close

Download Citation

Download a citation file in RIS format that can be imported by all major citation management software, including EndNote, ProCite, RefWorks, and Reference Manager.

Format: